bobcat - centrum nápovědy [help center]

Tato stránka je pouze pro čtení. Můžete si pouze prohlédnout zdrojový kód, ale ne ho měnit. Zeptejte se správce, pokud si myslíte, že něco není v pořádku.
====== Supplier Defect Report - receiving and confirmation ======

Once the SDR is submitted (the status is changed from //New// to //Submitted//) an email will be sent to the choosen contacts in the Supplier record.

{{:en:sdr-email-issue.png?600|}}

The SDR will also become visible on the Supplier view of the portal. The SDR is visible on the //Dashboard//

{{:en:sdr-dashboard.png?1000|}}

and also on the //List of defect reports//.

{{:en:list-of-defects.png?1000|}}

In both cases clicking on //detail// will open the SDR for editing.

===== Editing the SDR =====

==== SDR Header ====

{{:en:sdr-header.png?1000|}}

SDR header contains basic information like //SDR number// - unique identification of SDR, //Date submitted// - the date when SDR was sent to supplier, //Reply date// - the date when supplier first responded to issued SDR and //Status// - the current SDR status. There is no Supplier editable data in this section.

==== 1D ====

{{:en:sdr-1a.png?1000|}}

:!: Supplier editable data exist in this section. :!:

The **1D** section of SDR contains information of the defect occurence. Supplier name, address and contacts are displayed here. Defect location, founder of defect and severity level is also displayed here.

:!: Supplier must pay special attention to the following entries:
  * //To be reworked// - the defective part will be reworked
  * //RMA requested// - Bobcat is requesting the part to be shipped back to Supplier for inspection and/or rework
  * //Replacement requested// - Bobcat is requesting replacement parts for the defective quantity
  * //PO number// - the PO to be used to fulfill the replacement request


Below the thin line is displayed the name of Supplier responsible person to deal with the SDR and the box to enter the RMA number when requested by Bobcat.

==== 2D ====

{{:en:sdr-2.png?1000|}}

The **2D** section contains all information of the defective part and the defect itself. Defective part number, description and quantity as well as serial number (if exist) is entered by Bobcat Quality. Defect details together with accompanying pictures are filled to describe the extent of the defect.

To the right of the field the cost of the SDR is broken down to //Part cost// - piece part cost, //Rework cost// - cost of any internal or external rework, //Shipping cost// - cost of shipping the part to supplier (not filled if part is sent via provided RMA), //Incidental expeses// - cost not related to above categories and summed to //Total cost//.

:!: Supplier must pay special attention to the following entries:
  * //Part number// - Bobcat PN of the defective part
  * //Quantity// - quantity of defective parts
  * //Defect description// - details of the defect together with pictures
  * //Total cost// - cost of the SDR to be invoiced to Supplier

There is no Supplier editable data in this section.

==== 3D ====

{{:en:sdr-3a.png?1001|}}

:!: Supplier editable data exist in this section. :!:

In the **3D** section Bobcat and Supplier start the communication about the analysis of the corrective actions for the identified defect. Typically all SDR will contain information from Bobcat Quality about the //Interim Containment Action(s)//. The same is required from the Supplier. Aditionally the Suplier must provide information for the disposition of the defective parts. There are three choices where only one can be chosen.

:!: Supplier must pay special attention to the following entries:

  * //Defective parts// - the single choice selection where Supplier selects the disposal of parts
  * //Supplier action(s)// - the section where Supplier is required to fill in info about ICA

**WARNING** Entering comments will not automatically save data entered in the main SDR form. The SDR must be saved after comment is entered. **WARNING** 


===== Saving the SDR =====

{{:en:sdr-save.png?1000|}}

:!: Supplier editable data exist in this section. :!:

To save your changes to the SDR it is important to trully SAVE the SDR. Saving is done by clicking on the //change// button.


===== Main Menu =====

  * [[en:start|Back to Main menu]]

  * [[Supplier Defect Report - lifecycle]]
  * [[Supplier Defect Report - receiving and confirmation]]
  * [[Supplier Defect Report - adding comments and editing]]
  * [[Supplier Defect Report - verification of actions and closing]]
bobcat - centrum nápovědy [help center]

Uživatelské nástroje

Nástroje pro tento web

Nástroje pro stránku
